PoE Splitter with MicroUSB Plug - Isolated 12W - 5V 2.4 Amp
ADA 3785
A PoE splitter with Ethernet output and 5V 2.4A power supply.
Customers who bought this product also bought:
- Flanged Weatherproof Enclosure With PG-7 Cable Glands
- PLA 170 Cutting Pliers 1mm diagonal cut
- 5V 1.5A Output PoE Module - Works with Raspberry Pi 3 B+
- Peristaltique pump 12V for liquid with silicone tubes
- Long 5 connectors male 1 X 16 extra 2.54 mm strip lot
- Peristaltique pump 5V to 6V for liquid with silicone tubes
- Raspberry Pi 3 - Model B+ - 1.4GHz Cortex-A53 with 1GB RAM
More info
Power over Ethernet (PoE) distributors can make your project child's play - and most importantly, they work to connect any 802.3af compatible router to any Ethernet device, even if it does not natively support PoE ! The splitter takes a unified PoE signal (data and power) from an RJ-45 cable, then splits the data (Ethernet) and power (5 VDC regulated) into two different lines for non-PoE devices.
It is a 5V 2.4A PoE insulated separator with MicroUSB plug based on the IEEE 802.3af standard, economical, practical, efficient and reliable. It can split the power and data signals of a network cable, and can be used with any IEEE 802.3af compatible PoE injector, and provide power and data for non-PoE network equipment.
Whew, that's a lot of words - but basically : Connect this to your PoE switch or hub, then on the other side of the Ethernet cable, you'll get Ethernet and high quality 5V power, up to 2.4 Amps.
It is perfect for use with a Raspberry Pi model B, B+, Pi 2 or Pi 3 since these have Ethernet power supply and USB micro, and 2.4 Amp. It also works very well with Arduino cards and compatible cards that have Ethernet and micro USB. It would also be a perfect addition to a Feather card with FetherWing Ethernet.
Please note that, like many active PoE separators, there is a minimum load requirement of at least 100mA on the 5V power supply. We don't think this will be a problem since everything that has Ethernet will tend to draw 200mA+, but keep it in mind!
Use only with real 802.3af routers!
Ethernet cable length: 205mm / 8".
MicroUSB cable length: 205mm / 8".
Body dimensions: 80mm x 30mm x 24mm / 3" x 1" x .8" x .8".
Features :
Complies with IEEE 802.3af standard
Supports 10/100M data transmission (not for Gigabit ethernet)
Supports 48V unsolicited power over Ethernet PoE switches/hubs/adapters with 44V-57V power input
Operating temperature: 20°C - 45°C
Storage temperature: - 30°C - 70°C
Insulation: 2.5 kV
Power input : 44~57V DC
Output power: 5V DC 2.4A
Product Weight: 54.1g / 1.9oz
Accessories
- 6,18 € Add to cart
- 3,00 € Add to cart
- 4,80 € Add to cart
Ethernet FeatherWing for Feather card
FeatherWing card to add Ethernet connectivity to your Feather card
23,94 € Add to cartPassive PoE injection cables Pack
A lot of cable allowing an injection and extraction on the principle of the PoE Ethernet.
7,14 € Add to cartCable Gland - Waterproof RJ-45 / Ethernet connector
A cable gland with RJ45 connector for your wet projects.
9,54 € Add to cart