Customers who bought this product also bought:
- NeoPixel Ring - 12 x 5050 RGBW LEDs w/ Integrated Drivers - Natural White - ~4500K
- I2C voltage converter two-way 4-bit - BSS138
- HC-SR04 ultrasound distance sensor
- USB cable with switch and micro USB connector
- Adafruit Monochrome lattice Driver PCB for 4 x 4 Keypad & LED 3mm
- 4 X RGB Flora Smart Neopixel Version 2 - Adafruit
- PI T-Cobbler more Breakout Kit for Raspberry Pi
- Rotary encoder 24 positions with validation + knob
- Keyboard Silicone elastomer 4 x 4 - for 3mm LED
More info
Plug in and turn on, this Adafruit NeoPixel LED strip light with JST PH Connector has a total of 30 LEDs in a spacing of "60 LEDs per meter", and is 0.5 meters long, in elegant Adafruit black. It's not too long, but it has a lot of light action. Perfect for use with Hallowing, or a custom design with a JST PH plug.
The tapes are supplied in 0.5 metre reels with three 100 mm long wires connected to a 3-pin JST PH socket. The other end is sealed. The wires are even nicely color-coded: black for ground, green for signal, red for 3-5VDC power supply. We use SK6812 LEDs on these strips so that you do not need an in-line resistor and they work up to 3V logic + power.
NeoPixels are addressable LEDs. This means that there are 60 RGB LEDs per meter and the strip is half a meter long, you get 30 individually controlled RGB LEDs! You can adjust the color of each red, green and blue component of each LED with a PWM accuracy of 8 bits (i.e. 24 color bits per pixel). The LEDs are controlled by shift registers that are chained along the strip so that you can shorten the strip if you wish by cutting it. Only one digital output pin is required to send the data. The PWM is integrated into each LED chip so that once you have defined the color, you can stop talking to the strip, and it will continue to PWM all the LEDs for you.
The tape is made of a flexible printed circuit board material and is delivered in a weatherproof coating. You can cut this thing quite easily with a cutting pliers. Of course, you can also connect the strips together to extend them, just look at how much power you need! You must use a 3-5V DC power supply to power these tapes, do not use more than 6V or you can destroy the entire tape!
These LEDs use about 4.8 Watts max (~1 Amps @ 5V) per meter. The maximum value assumes that all LEDs are completely white, usually the actual current for colored models is less than 1/3 of the maximum current. A good power supply is the key!
Features
Dimensions with coating: 500 x 14 x 6mm
60 LEDs per meter
Removable waterproof housing IP20/65
Maximum 5V @ 60mA per LED (all LEDs in full brightness)
5VDC power supply (do not exceed 6VDC) - no polarity protection
1 integrated RGB LED per segment, individually controllable
LED type: SK6812
LED wavelength: 630nm/530nm/530nm/475nm
Connector: 3-pin JST PH
Product dimensions: 500.0 mm x 14.0 mm x 14.0 mm x 6.0 mm / 19.7" x 0.6" x 0.2" x 0.2
Product Weight: 24.0g / 0.8oz
Documentation
Accessories
Adafruit NeoPixel LED Strip w/ Alligator Clips - 30 LED/m - 1 Meter Long - Bl...
1m black LED strip with crocodile clips.
17,94 € Add to cart- 41,94 € Add to cart